21 Search Results

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO₂ thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb₂Si₂O₇ EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO₂ TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation frommore » β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.« less

The issue of fuel fragmentation, relocation, and dispersal is critical in the licensing and use of high-burnup (>62 GWd/MTU) nuclear fuel in light water reactors (LWRs). In this work, two test series are reported that examine the fragment dispersal during a burst event and an additional dispersal following the burst due to vibrations in the rod, such as those induced by accident recovery systems. To examine dispersal during the balloon and burst portion of a Loss-of-Coolant Accident event, HfO₂ fragments and yttria-stabilized zirconia pellets were filled into an as-fabricated cladding tube, which was then pressurized and subjected to loss-of-coolant accidentmore » testing in steam. Results from this test were found to be highly non-prototypic, and dispersal was both significantly more violent and significantly greater in magnitude than identified for actual fuel tests. These findings were attributed to the conservative (more dispersive) nature of the particles chosen for dispersal and to the details of the test conditions used that led to particularly wide bursts. Further, the second set of tests examined dispersal following the burst when vibrations were induced in the rod, primarily via recovery activities such as Emergency Core Cooling System actuation leading to rapid water addition. Post-burst dispersal testing was performed by inducing sinusoidal oscillations with 2–25 nm peak-to-peak amplitude and 2–5 Hz frequencies in pre-burst rods that had been refilled with HfO₂ fragments or high-burnup fragment surrogate mixture of HfO₂ fragments and yttria-stabilized zirconia sands. Testing revealed that rods with large burst openings (7 mm wide in this work) led to unmitigated dispersal from above the burst zone but that smaller bursts (5 mm wide), although still much larger than the mean fragment size of 3 mm, led to effectively no dispersal because of interparticle locking. Additionally, mixture and moisture were found to impact the amount of dispersal: mixtures increased dispersal, and moisture drastically reduced it. The implications of these findings on likely dispersal from actual fuel are discussed.« less

Understanding fuel system behavior during postulated loss-of-coolant accidents is pertinent for continued safe and efficient operation of light water reactors, particularly as higher burnups are being pursued and safety margins re-evaluated. Conventional mechanical models for the incumbent Zr alloys typically rely on the assumption that steady-state creep is the dominant fuel cladding response during transient accident conditions. To investigate this assumption, simulated accident burst testing was performed on Zircaloy-4 claddings with balloon behavior measured in-situ. Here, two distinct loading conditions were utilized during burst testing: (1) constant-gas-inventory where pressure was allowed to increase with temperature and (2) constant pressure. In-situmore » strains and strain rates were measured via 2-dimensional digital image correlation techniques and synchronized with temperature to determine deformation dependencies. The temperature dependence of strain rate was characterized by a two segment Arrhenius relationship, with a distinct transition between the high and low temperature/strain regimes. The average activation energy of the lower temperature/strain regime was 328 ± 25 kJ/mol, in agreement with the ~320 kJ/mol used for conventional LOCA models. However, the higher temperature/strain segment, which encompassed most of ballooning, showed increased activation energies as well as a dependence on whether the burst region was in view. For tests that burst away from the camera view, the average high temperature/strain segment activation energy was 635 ± 150 kJ/mol. For samples where the rupture opening formed in view, the average activation energy was 1015 ± 179 kJ/mol. This observed shift in temperature dependence indicates a transition in deformation mechanism at the end of life, possibly to time independent failure mechanisms, which has not yet been visualized in the literature for Zr alloys. Parameters at the transition points were analyzed to determine thresholds for this change in behavior, which occurred at an average hoop strain of 6.9 ± 2.1 %.« less

Here, SiC preforms were infiltrated with polycarbosiloxane preceramic polymer to create low-cost SiC—Si_xO_yC_z matrix composites for possible high temperature application. The effect of specimen annealing conditions on the steam and air oxidation resistance was analyzed. Air exposures from 900–1500°C showed stability of the Si_xO_yC_z matrix phase with moderate oxidation resistance. After 900°C exposures, oxidation of the composite is primarily limited to the matrix phase, and only at 1200 and 1500°C was SiC consumption visualized. Steam cycle exposures at 1200°C resulted in rapid linear oxidation of the composites with induced specimen swelling from volume expansion associated with internal oxidation. Specimens annealedmore » in argon were found to be the most oxidation resistant due to increased matrix crystallinity and carbon retention. The results of this work were used to develop clear strategies for improving the high-temperature properties of SiC—Si_xO_yC_z composites.« less

In-situ strain measurements of fuel cladding can enable high-throughput data collection and validation to support accelerated qualification of cladding materials. Here, in this work, 3D digital image correlation was used to map strain for both Zircaloy-4 (Zry-4) and Cr-coated Zry-4 during two types of cladding rupture experiments: isobaric temperature ramp tests at 5 °C/s and isothermal pressure jump tests at 600 °C. Zry-4 strain data initially showed a temperature dependence expected for creep deformation, yet a shift to a new plastic deformation mechanism not reported in literature dominated during the finals seconds prior to rupture. Cr-coated Zry-4 did not showmore » the change in deformation mechanism at the end of life and showed a delay in measurable creep deformation. Stress dependences were similar for Zry-4 and Cr/Zry-4 during pressure jump tests. Cr-coatings were found to decrease the strain rate during both testing scenarios. Creep parameters were calculated to support modelling efforts regarding design basis accidents.« less

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb₂SiO₅ secondary phase displayedmore » a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb₂SiO₅ concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.« less

To accurately model the long-term durability of environmental barrier coatings (EBCs), a more complete understanding of the phase composition and transformations of the thermally grown oxide SiO₂ (TGO) is desired. For the TGO formed during thermal cycling in steam, cristobalite formation and the subsequent β- to α-cristobalite transformation has been identified as a potentially life-limiting mechanism. In this study, Raman micro-spectroscopy was used to quantify the cristobalite transformation on a polycrystalline Si coupon that was exposed to steam at 1350°C for 100 h. The phase transformation was mapped at 200–260°C on the TGO surface at different ramp rates using amore » heating stage and a micro-positioning stage. The stress in the Si substrate was also determined using Raman spectroscopy by measuring the stress induced peak shift. The α→β phase transformation produced a 300–500 MPa tensile stress in the Si substrate, which compared well to the stress predicted from the volumetric expansion of the cristobalite. In conclusion, quantifying the phase transformation and residual stress are critical tools in developing the next generation of high performance EBCs.« less

The process for developing and qualifying nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and postirradiation examinations; and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes ~20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in situ measurements to assess materialmore » performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In situ measurements generally provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the US nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the US Nuclear Regulatory Commission (NRC) outlined in its research information letter several technical issues that the industry must address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heat-up phase. By leveraging these advanced in situ capabilities, this work used in situ data generated from a simulated LOCA to better understand high-temperature creep and its effect on Zircaloy balloon and rupture performance. Here, this work used the BISON fuel performance code to assess the high-temperature creep model predictions with in situ data.« less

Cr-coated zirconium alloys represent a modern approach to enhance cladding safety during accident scenarios. Two high-power impulse magnetron sputtered Cr-coated Zry-4 systems were subjected to simulated loss-of-coolant accident conditions to investigate cladding performance. The first Cr-coating (4.8 µm thick) was deposited onto Zry-4 cladding and exhibited through-thickness cracking while the second Cr-coating (6.8 µm thick) was deposited with improved deposition parameters onto polished Zry-4 and exhibited no cracking. During burst testing, the coating with a higher density of defects failed to consistently reduce oxidation and exhibited similar burst behavior as Zry-4. In contrast, the second Cr-coating reduced ZrO₂ formation throughmore » formation of Cr₂O₃ and displayed enhanced burst temperatures by ~80 °C compared to Zry-4. Utilizing an empirical relation for burst behavior of zirconium alloys, the 6.8 µm Cr/Zry-4 system displayed enhanced burst temperatures equivalent to an effective 0.464 mm increase in Zry-4 wall thickness, highlighting the value of continuous Cr coatings for accident scenarios.« less

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO₂ at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas themore » YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.« less